Artwork

Content provided by inyopools.com. All podcast content including episodes, graphics, and podcast descriptions are uploaded and provided directly by inyopools.com or their podcast platform partner. If you believe someone is using your copyrighted work without your permission, you can follow the process outlined here https://player.fm/legal.
Player FM - Podcast App
Go offline with the Player FM app!

Episode 16: Why is My Pump Motor Clicking?

5:08
 
Share
 

Manage episode 154059093 series 1111959
Content provided by inyopools.com. All podcast content including episodes, graphics, and podcast descriptions are uploaded and provided directly by inyopools.com or their podcast platform partner. If you believe someone is using your copyrighted work without your permission, you can follow the process outlined here https://player.fm/legal.
Why is my pool pump motor making a clicking sound? All pool pump motor troubleshooting should begin with the easiest solutions; first begin with voltage. Blog Post: http://goo.gl/WXpSr3 A couple of reasons why this could be happening. The first would be that dual voltage motors, such as the UST1102, are shipped from the factory set to 230 volts. If you install the motor on a 115-volt circuit without setting the volt switch to the proper setting the motor may not start. The lower voltage may allow the motor to spin but not to full RPMs; the clicking sound is the governor/centrifugal switch opening and closing because the motor is not at full speed, 3450 RPMs. The volt switch is either a jumper or a knob style shown in the picture. The notch in the knob selects the current voltage setting. Another reason why you could hear clicking is if your old motor was a full rated motor and your newer motor is an up rated motor, which means that the full rated motor has a higher service factor; it’s stronger. So when you put an uprated, a weaker motor, on there it’s not strong enough to spin the impeller for a full rated system. So that could also cause the clicking. For a full explanation on uprated and fullrated, read our blog article: Is a 1.0HP Motor the Same as a 1.5HP Motor? Century Motor Dual Voltage Switch Century Pump Motor Terminal Board w/ Volt Knob After we helped Jim by explaining the two options he ran through a troubleshoot and figured he had it set on the incorrect voltage. He turned the knob to 115 volts and the motor fired up without a problem. Sometimes it really is the simplest solution to pool problems. After we helped Jim by explaining the two options he ran through a troubleshoot and figured he had it set on the incorrect voltage. He turned the knob to 115 volts and the motor fired up without a problem. Sometimes it really is the simplest solution to pool problems. If you have any more questions about pool pump motor troubleshooting, you can always contact us at 877-372-6038 or visit us online at www.INYOpools.com. You can e-mail us at upload@inyopools.com, also subscribe to this video and to our newsletter where you can also get a free pool maintenance guide, 128 pages that’s what they tell me.
  continue reading

24 episodes

Artwork
iconShare
 
Manage episode 154059093 series 1111959
Content provided by inyopools.com. All podcast content including episodes, graphics, and podcast descriptions are uploaded and provided directly by inyopools.com or their podcast platform partner. If you believe someone is using your copyrighted work without your permission, you can follow the process outlined here https://player.fm/legal.
Why is my pool pump motor making a clicking sound? All pool pump motor troubleshooting should begin with the easiest solutions; first begin with voltage. Blog Post: http://goo.gl/WXpSr3 A couple of reasons why this could be happening. The first would be that dual voltage motors, such as the UST1102, are shipped from the factory set to 230 volts. If you install the motor on a 115-volt circuit without setting the volt switch to the proper setting the motor may not start. The lower voltage may allow the motor to spin but not to full RPMs; the clicking sound is the governor/centrifugal switch opening and closing because the motor is not at full speed, 3450 RPMs. The volt switch is either a jumper or a knob style shown in the picture. The notch in the knob selects the current voltage setting. Another reason why you could hear clicking is if your old motor was a full rated motor and your newer motor is an up rated motor, which means that the full rated motor has a higher service factor; it’s stronger. So when you put an uprated, a weaker motor, on there it’s not strong enough to spin the impeller for a full rated system. So that could also cause the clicking. For a full explanation on uprated and fullrated, read our blog article: Is a 1.0HP Motor the Same as a 1.5HP Motor? Century Motor Dual Voltage Switch Century Pump Motor Terminal Board w/ Volt Knob After we helped Jim by explaining the two options he ran through a troubleshoot and figured he had it set on the incorrect voltage. He turned the knob to 115 volts and the motor fired up without a problem. Sometimes it really is the simplest solution to pool problems. After we helped Jim by explaining the two options he ran through a troubleshoot and figured he had it set on the incorrect voltage. He turned the knob to 115 volts and the motor fired up without a problem. Sometimes it really is the simplest solution to pool problems. If you have any more questions about pool pump motor troubleshooting, you can always contact us at 877-372-6038 or visit us online at www.INYOpools.com. You can e-mail us at upload@inyopools.com, also subscribe to this video and to our newsletter where you can also get a free pool maintenance guide, 128 pages that’s what they tell me.
  continue reading

24 episodes

All episodes

×
 
Loading …

Welcome to Player FM!

Player FM is scanning the web for high-quality podcasts for you to enjoy right now. It's the best podcast app and works on Android, iPhone, and the web. Signup to sync subscriptions across devices.

 

Quick Reference Guide